進口自來水過濾器德國洛克《DE LOCKE》現貨供應 

一、進口自來水過濾器概述：

德國《LOCKE》洛克進口自來水過濾器（Inlet water filter）是使用水力控制閥及精密的易堵塞的機械產品所必須具備的過濾設備。是輸送介質的管道系列不可缺少的一種裝置，通常安裝于水力控制閥、減壓閥、泄壓閥、定水位閥等設備的進口端，用來消除介質中的雜質，防止顆粒性雜質進入通道，造成墻塞，以保護設備管道上的配件免受磨損和堵塞。

Locke imported water filter is a kind of filtration equipment which is necessary for using hydraulic control valve and precise mechanical products easy to block. It is an indispensable device for the pipeline series of medium transmission, which is usually installed at the inlet end of hydraulic control valve, pressure reducing valve, pressure relief valve, constant water level valve and other equipment, to eliminate impurities in the medium, prevent particulate impurities from entering the channel, and cause wall plug, so as to protect the accessories on the equipment pipeline from wear and blockage.

二、進口自來水過濾器技術參數：

1、規格范圍：DN15-DN500

2、溫度范圍：-40℃≈500℃

3、壓力范圍：PN16-PN320

4、閥體材質：不銹鋼

5、濾網材質：不銹鋼

6、連接方式：法蘭

7、適用范圍:自來水

1. Specification range: dn15-dn500

2. Temperature range: - 40 ℃ ~ 500 ℃

3. Pressure range: pn16-pn320

4. Valve body material: stainless steel

5. Filter screen material: stainless steel

6. Connection method: flange

7. Scope of application: tap water

三、進口自來水過濾器說明書:

1.進口自來水過濾器在使用一段時間后，需要取下內部的過濾網進行清洗，以免被過濾的雜  質堵在過濾網上增加了液體阻力，影響系統水的正常流通，一般每3個月清洗一次過濾網  為佳；
2.清洗后的過濾網在安裝回進口自來水過濾器后，注意觀察進口自來水過濾器墊片是否有漏   水情況發生，如果發現滲漏，及時更換密封墊片；
3.新系統安裝進口自來水過濾器幾小時后要及時清洗濾網，以防管道安裝時殘留在管道內的   施工垃圾堵塞進口自來水過濾器；
4.用于不經常流動的系統的進口自來水過濾器要特別注意衛生問題，系統超過4天不運行，   進口自來水過濾器過濾網上就容易滋生細菌，要注意及時清洗過濾網。

1. After using the imported tap water filter for a period of time, it is necessary to remove the internal filter screen for cleaning, so as to avoid the impurities blocked on the filter screen increasing the liquid resistance and affecting the normal flow of the system water. Generally, it is better to clean the filter screen once every three months;

2. After the cleaning filter screen is installed back to the inlet tap water filter, pay attention to observe whether the gasket of the inlet tap water filter leaks. If leakage is found, replace the gasket in time;

3. The filter screen shall be cleaned in time several hours after the installation of the inlet water filter in the new system to prevent the construction waste remaining in the pipeline from blocking the inlet water filter during the installation of the pipeline;

4. Pay special attention to the sanitation of the imported tap water filter used in the system that does not flow frequently. If the system does not operate for more than 4 days, the filter net of the imported tap water filter is easy to breed bacteria, and the filter net should be cleaned in time.