●Precautions for Mounting （安裝注意事項）

Unlike other electronic components, Lithium Manganese Dioxide Battery(Coin-type) may be externally short-circuited before and after it is installed in circuit boards and without the power being turned on. This causes power drainage. As a result, the battery may lose its capacity before the equipment is even used. As short-circuits tend to occur in the following cases, please take care when handling the battery.

（不同其它電子零件，鋰-二氧化錳電池（扣式）在安裝到電路板前后可能會外部短路，同時動力未開啟。這會造成動力流失。因此，甚至在設備使用之前電池就可能會損失它的容量。例如短路發生在以下情況下，請謹慎操作電池）

1. Overlapping Batteries （重疊電池）

Lithium Manganese Dioxide Battery is shaped as shown below. It has exposed positive(+)and negative(-) metallic surfaces with a thin cylindrical seal, called the gasket, inbetween them. When the batteries are overlapped or mixed together in a disorderly way, their positive(+)and negative(-)terminals touch each other, causing short-circuits.（鋰-二氧化錳電池形狀如下所示。它敞開的正極與負極間僅僅由一圈很窄的環狀（密封圈）相隔離，當電池雜亂地重疊堆放時，它們的正極 (+)和負極(-)端會相互接觸而造成短路）

2. The Batteries Put in a Metallic Container or on a Metallic Plate

（將電池放入金屬容器或金屬盤里）

Similar to the overlapping battery problem, when the batteries are put in a metallic container or on a metallic plate, their positive(+)and negative(-)terminals may short-circuit through the conductive surface, depending on how the batteries are position.

（與重疊電池問題相似，當電池放到金屬容器或金屬盤里，它們的正極 (+)和負極(-)端可能會通過導電性的表面和電池的位置而造成短路）

3. When The Battery is Held with Metallic Tweezers （當用金屬鑷子夾電池時）

When held with a pair of metallic tweezers as shown, the battery short-circuits through the tweezers.（當用一副金屬鑷子夾電池時，電池通過金屬鑷子短路）

4.  When The Battery Lead Plates Touch Each Other （當電池引線相互接觸時）

When the battery lead plates bend and touch each other or other either terminal, the battery short-circuits.（當電池引線彎曲并相互接觸或其它接線端接觸時，電池短路）

5. Solder Bridges （焊橋）

Solder may bridge between circuit board conductors, causing a short-circuit and draining the battery.（焊接可能橋連電路板導體，造成短路，耗盡電池）

6. Short-circuits through Soldering Irons （通過烙鐵短路）

Similar to solder bridging, when the circuit board wiring is short-circuited by a soldering iron for an extended period the battery is drained and consumed. Complete short-circuits through soldering irons within 5 seconds.（與焊橋相似，當電路板線路被烙鐵超時接觸時引起短路，電池能量將會流失并耗盡。通過烙鐵短路應在5秒內結束）

7. Short-circuits through Piled Circuit Boards （通過堆疊的電路板短路）

When circuit boards with the batteries are piled on top of one another, their conductive traces may touch and form a battery discharge circuit that consumes the battery's power.

（當加載電池的電路板相互堆疊，它們導電性的線路會接觸而形成電池放電電路消耗電池能量）

3V扣式帶焊插腳電池標稱電壓3V,是干電池的2倍,它采用化學性質非常穩定的二氧化錳為正極材料和比能量非常高的鋰為負極材料。年自放電率低于2%，儲存壽命長。電池采用合理密封結構和材料,氣密性良好,使用很。鋰錳電池具有溫度寬的特點,在-40℃-+80℃下電池均能正常工作,有效存儲期為一年。鋰錳扣式電池廣泛適用于電腦主機板、電子詞典、照相機、遙控器、耳溫槍、血糖測試儀、體脂肪測試儀、汽車輪胎壓力計、電子稱、萬年歷、玩具、鐘表、考勤機、MP3、收音機、電子閃光產品等。 公司的產品品種及規格如下： 3V扣形帶焊插腳電池：CR2032/1HF、CR1616/1F2、CR2016/1F2、CR2032/1F4、CR2330/1HF、CR2330/1VC、CR2354/1HF、CR2354/1GU、CR1225/1HC、CR1225/1VC、CR1632/1HF、CR2032/1GU、CR2032/1HE、CR2032/1F2、CR2325/1HG、CR2330/1HE等等規格型號 我們可以為各種型號的電池加工上焊腳，根據客戶的圖紙、電池樣品。可準時在國內交貨，請貴公司確定所需規格、數量及交貨方式，我公司將盡快給予報價，若需樣品及規格書請告知。