美標門鎖

規格與性能

SPECIFICATION:

·執行標準：美國ANS|A156.13-2005—級鎖標準，通過100萬次轉動測試

Certification and Compliance: ANSI A156.13-2005, Grade 1

中國GB12955-2008防火標準,90分鐘防火標準

GB12955-3008 Fire rated 90 mins

·鎖體：高強度鋼質鎖體

Lockcase: Heavy gauge steel, with zinc dichromate finish for corrosion resistance

固定式方舌：精鑄不銹鋼,1“(25mm)行程，配備肪鋸淬火銅輥

Deadbolt: One-piece stainless steel, 25mm throw

·斜舌：精鑄不銹鋼三段式,3/4“(19mm)長，帶抗摩擦前導舌

Latchbolt: Stainless steel, 2 piece mechanical with anti-friction insert 19mm throw

·輔助保險舌：精鑄不銹鋼

Auxiliary Latchbolt stainless steel

·鎖扣板：不銹鋼，不分左右手，采用ANS標準尺寸1-1/4‘×4-7/8(32mmx124mm)·

Strike stainless steel， ANSI straight lip standard4-7/8"(124mm)x1-1/4"(32mm)

適用門厚1-3/8’(35mm)2-1/2‘(64mm)，標準門厚1-3/4‘(45mm)

Door Thickness: 1-3/4"(45mm)standard. Optional 1-3/8"(35mm), 2-1/2‘(64mm)

安裝中心距2-3/4’(70mm)

Backset: 2-3/4"(70mm)

表面處理；不銹鋼拉絲、沙金PVD。亮金PVD、拋光

Finish: Stain Steel Satin PVD. Polished PVD. Polished

美標插芯鎖要求和檢驗方法

ANSI/BHMA A156,13MORTISE LOCK

適用范圍APPLICATION SCOPE

本標準規定了美式插芯鎖性能要求，包括壽命測試，功能測試、安全測試、材料評估測試、表面處理測試及尺寸標準依據該標準，插芯鎖具的性能等級和安全等級分別分為3級。各級別性能要求如下：

This Standard establishes performance requirements for mortise locks and latches, which includes cycle tests, strength tests, operational tests, security tests, material evaluation tests. finish tests and dimensional criteria. Two Classifications of Grades are described in this standard, Operational grade

and Security Grade, The minimum acceptable Grade lever of both is grade 3.The tests and requirements of all grades are as follows

1.轉動旋鈕擰開鎖舌需要的力：

所有級別最大:9lbf-in(1Nm)

Torque to retract dead bolt or torque to retract dead bolt and latch bolt by turn

Requirements Maximum all grades: 9 lbf-in(1 Nm)

2.轉動鑰匙擰開鎖舌需要的力

所有級別最大:9lbf-in(1Nm)

Torque to retract dead bolt or torque to retract dead bolt and latch bolt by key

Requirement maximum. All Grades: 9 lbf-in(1Nm

3.轉動球形把手或者水平把手?jǐn)Q開鎖舌

需要的力：

所有級別最大：

球形把手:9|bf-in(1Nm)

水平把手:28|bf-in(1Nm

入戶帶按鈕的大門鎖

所有級別:9lbf-in(1Nm)

Force or torque to retract latch by knob or lever.

Requirements maximum:

Knob-all grades: 9 lbf-in(1Nm)

Lever-all grades: 28 lbf-in( 1Nm)

Entry handleset thumb piece:

Requirements Maximum All grades: 9 lbf-in( 1Nm)

4.閉門力

所有級別最大4.5lbf(20N

Force to latch door

Requirement Maximum: All grades 4.5 lbf (20N)

5.門鎖閉時斜舌伸出長度

最?。阂患?jí):9/6in。(14.3mm)

二級和三級:8/3in。(9.5mm)。

Minimum projection of auxiliary dead latch to deadlock latch bolt

Requirements minimum Grade 1: 9/6 in (14.3mm), Grade 2 and 3: 8/3 in. (9.5mm)

6.副方舌伸出的長度：

最?。阂患?jí)3/8in(9.5mm

二級和三級:5/16in(79mm)

Minimum projection of auxiliary dead latch to deadlock latch bolt:

Requirements minimum Grade 1: 3/8 in. (9.5mm), Grade 2 and 3: 5/16 in (7. 9mm)

7門彎曲試驗：

所有級別最大：

球形把手:45|bf-in(5Nm)

水平執手:70bfin(8Nm)

按鈕40bf(180N)

平板拉手:65|bf(290N)

Warped door test

Requirements for Maximum all grades

Knob: 45 Ibf-in( 5Nm)

Levers: 70 lbf-in( 8Nm)

Thumb pieces: 40lbf(180N

Paddles: 65Ibf(290N)

8.鎖舌強度：

斜舌強度最小：所有級別:1200|bf(5300N)

方舌強度最?。核屑?jí)別:1350bf(6,000N)

Bolt strenght test:

Requirements:

Latch Bolt minimum: All grades: 1200 Ibf(5, 300N)

Dead Bolt minimum: All grades: 1350 Ibf(6, 000N)

9.軸負重測試

所有級別最小：

球形把手，水平執手位于軸心時:500|bf(2,200N)

水平執手距軸心2in(51mm)時:360lbf(1600N)

按鈕:150lbf(2200N)

距軸心2in(51mm)時:225|bf(1000N

Axial Load Test

Requirements All Grades minimum:

Knobs, levers at the spindle or grips: 500 lbf(2, 200N)

Levers 2 in(51mm)from spindle: 360 lbf( 1600N)

Thumb pieces: 150 lbf(2200N)

Paddles: at the axle: 2 in(51 mm) from the axle: 225 lbf(1000N)

10.垂直負重測試

一級:360|bf(1600N)

二級:250|bf(1100N

三級:150lbf(670N)

Vertical Load Test

Grade 1: 360 lbf(1600N)

Grade2:250|bf(1100N)

Grade 3:150 lbf(670N)

11.門鎖閉時外水平執手扭力測試：

所有級別最小:450lbf-in(50Nm)

Locked Outside Lever Torque Test:

Requirements: All Grades minimum: 450 lbf-in( 50Nm)

12.門未鎖閉時水平執手扭力測試：

所有級別最小:450lbf-in(50Nm)

Unlocked Lever Torque Test

Requirements: Lever Torque minimum: All Grades: 450 lbf-in( 50Nm)

13.門未鎖閉時入戶門鎖負重測試：

所有級別最小:70|bf-in(310Nm)

Unlocked Entry Handle set load Test:

Requirements: Unlocked Entry Handle set minimum: All

Grades: 70 lbf-in(310Nm)

SECUR| TY TEST安全測試

1.球形把手，水平執手或平板拉手沖擊力測試：

一級:75lbf-ft(100J)10次沖擊

二級:75|bf-ft。(100J)5次沖擊

三級:75|bf-ft.(100J)2次沖擊

Knob, Lever or Paddle Impact Test:

Requirements:

Grade 1: 75lbf-ft (100J)10 blows

Grade 2: 75lbf-ft (100J )5 blows

Grade 3: 75lbf-ft (100J)2 blows

2.鎖芯護片及鎖眼扣沖擊力測試：

一級:75lbf-ft(100J)10次沖擊

二級:75lbf-ft(100J)5次沖擊

三級:75lbf-ft。(100J)2次沖擊

Cylinder guard or Escutcheon Impact Test:

Requirements:

Grade 1: 75Ibf-ft (100J)10 blows

Grade 2: 75lbf-ft (100J )5 blows

Grade 3: 75lbf-ft (100J)2 blows

3.鎖芯護片及鎖眼扣拉手測試：

一級:3600lbf-ft.(16,000N)

二級:2500lbf-ft.(11.000N

三級:1000|bf-ft(4,400N)

Cylinder guard or Escutcheon Tension Test:

Requirements:

Grade1:3600lbf-ft.(16,000N

Grade2:2500lbf-ft.(11,000N

Grade3:1000lbf-ft.(4,400N)

4.鎖芯體及鎖芯殼的拉手測試：

一級:3600|bf-ft.(16,000N)

二級:2500|bf-ft.(11.000N)

三級:1000lbf-ft.(4,400N)

Cylinder body or housing tension Test

Requirements:

Grade1:3600|bf-ft.(16,000N

Grade2:2500lbf-ft.(11,000N)

Grade3:1000lbf-ft.(4,400N)

5.鎖閉的球形把手，水平執手，平板拉手測試，球形把手扭力

一級:175|bf-ft.(240Nm)

二級:120lbf-ft.(160Nm)

三級:55lbf-ft.(75Nm

Locked Knob. Lever or Paddle Test

Requirements:

Knobs Torque

Grade 1: 120 lbf-ft (160Nm)

Grade 2: 80 lbf-ft (110Nm)

Grade 3: 35 lbf-ft (47Nm)

水平執手扭力

一級:120lbf-ft.(160Nm)

二級:80lbf;ft.(110Nm)

三級:35|bft.(47Nm)

Lever Torque

Grade 1: 120 lbf-ft (160Nm)

Grade 2: 80 Ibf-ft (110Nm)

Grade 3: 35 lbf-ft (47Nm)

平板拉手扭力

一級:675lbf(3000N)

二級:450|bf(2000N)

三級:225lbf.(1000N)

Paddle force

Grade1:675|bf.(3000N)

Grade 2: 450 lbf(2000N

Grade3:225|bf.(1000N)

6.鎖芯體和鎖芯殼扭力：

一級:120|bf-ft,(160Nm)

二級:80lbf-ft.(110Nm)

三級:35lbf-t(47Nm)

Cylinder body or Housing Torque Test:

Requirements

Grade 1: 120 lbf-ft (160Nm)

Grade 2: 80 lbf-ft (110Nm)

Grade 3: 35 lbf-ft (47Nm)

7.鎖芯護片和鎖眼扣扭力：

一級:120|bf-ft.(160Nm)

二級:80bf-ft.(110Nm)

三級:35|bf-t.(47Nm)

Cylinder Guard or Escutcheon Torque Test:

Requirements

Grade 1: 120 Ibf-ft, (160Nm)

Grade 2: 80 Ibf-ft (110Nm)

Grade 3: 35 Ibf-ft (47Nm)

8.鎖芯頭沖擊力測試

一級:75|bf-ft。(100J)10次沖擊

二級:75|bf-ft.100J)5次沖擊

三級:75lbf-ft。(100J)2次沖擊

Cylinder Face Impact Test:

Requirements

Grade 1: 75 lbf-ft (100J)10 blows

Grade 2: 75 lbf-ft (100J)5 blows

Grade 3: 75 lbf-ft (100J)2 blows

9.方舌或斜舌，或方舌和斜舌舌沖擊測試：

一級：在二緞的基礎上增加兩次150lbf-ft(200J)沖擊

二級：在一的基礎上增加兩次120lbf-ft160J)沖擊

三級:2次120lbf-t(160J)沖擊加上兩次9olb-ft(160J)沖擊

Dead Bolt or Latch Bolt or Dead Bolt and latch Bolt Impact Test Requirements:

Grade 1: Grade 2 requirements plus 2 blows of 150 lbf-ft (200J)

Grade 2: Grade 1 requirements plus 2 blows of 120 Ibf-ft (160J

Grade 3: 2blows of 60 lbf-ft(80J)plus 2 blows of 90 lbf-ft (120J

10.鎖舌壓力測試

所有級別最?。?/span>

斜舌:360|bf(1600N

方舌:600lbf(2700N

Bolt Pressure Test

Requirements: All Grades Minimum:

Latch Bolt: 360 Ibf(1600N)

Dead Bolt: 600 Ibf(2700N)

11.方舌鋸切試驗

所有級別:5分鐘

Dead Bolt Sawing Test:

Requirements: All Grades Five Minutes.

CYCLE TEST壽命測試

一級:1,000,000次

二級和三級:800,000次

Cycle requirements

Grade1:1,000.000

Grade 2 and 3: 800.000

FINISH TEST表面處理

1.鹽霧測試

中性鹽霧測試：

除鎖體面板和鎖片外所有有機涂層:96小時

鎖體面板和鎖片的有機涂層:24小時

無機涂層:200小時

Salt Spray Test

Neutral salt spray Test

Organic coatings on all parts except fronts and strikes 96 hours

Organic coatings on lock fronts and strikes: 24hours

Inorganic coatings: 200 hours

CASS鹽霧測試：

所有級別無機涂層:96小時

CASS Salt Spray Test

Requirements: All Grades: Inorganic coatings on all parts: 96 hours

2.濕熱度測試

除鎖體面板和鎖片外所有有機涂層:240小時

鎖體面板和鎖片有機涂層；48小時

Humidity Test:

Requirements all Grades

Organic coatings on all parts except fronts and strikes: 240 hours

Organic coatings on lock fronts and strikes: 48 hours

3.鉛筆硬度測試：

所有級別：帶有有機涂層的所有材料:4小時

Pencil Hardness Test

Requirements all grades: For all material with organic coatings: 4hours

4.平板摩擦測試:500次

Taber Test: Requirements: 500 cycles

5.汗液測試：

所有級別：帶有有機涂層的所有材料:4次。

Perspiration Test

Requirements All Grades: For all material with organic coatings: 4 cycles

6.紫外光及冷凝測試：

所有級別：所有涂層144小時

Ultra Violet Light and Condensation Test

Requirements: All Grades: all Coatings: 144 hours

MATERIAL EVALUATION TESTS

材料評估測試

球形把手變形測試：

一級：變形量不得超過10%

二級和三級：變形量不得超過25%

蓋板和鎖眼扣凹坑測試

一級:0.075in(1.9mm)

二級和三級:0.100in。(2.5mm

Knob crush Tests:

Grade 1: Deformation shall not exceed 10%

Grade 2 and 3: 25%

Rose and Escutcheon Dent Test

Requirements:

Grade 1: 0.075 in(1.9mm)

Grade 2 and 3: 0. 100in (2. 5mm