進口自由浮球式疏水閥產品報價-德國洛克 

二、進口自由浮球式蒸汽疏水閥性能特點：

1、唯一轉動的是高精度研磨的不銹鋼浮球，抗腐蝕。

2、結構簡單，維修方便。

3、不受壓力波動的影響，連續排水，噪聲小。

4、裝有自動排空裝置，能夠迅速排除空氣，防止氣堵和汽鎖。

5、體積小，排量大。

6、有水就排，能夠加快系統啟動速度。

1. The only rotating ball is the stainless steel floating ball with high precision grinding, which is corrosion-resistant.

2. Simple structure and convenient maintenance.

3. Not affected by pressure fluctuation, continuous drainage, low noise.

4. Equipped with automatic emptying device, it can quickly remove air and prevent air block and steam lock.

5. Small volume and large displacement.

6. Drain when there is water, which can speed up the start-up of the system.

一、進口自由浮球式蒸汽疏水閥產品簡介：

德國《LOCKE》洛克-進口自由浮球式蒸汽疏水閥利用高精度研磨不銹鋼空心浮球在閥腔內隨著凝結水的液位變化開啟或關閉閥門。該疏水閥的結構比較簡單,主要由浮球和自動排空裝置組成。閥腔內唯一的動作元件不銹鋼空心浮球,采用高精度研磨工藝制造,整個球面均可做密封面,工作時無集中磨損,使用壽命長 ; 閥腔內無易損件,可靠性高。浮球能根據水位變化而自由調節閥孔的開度,能夠連續排放凝結水,過冷度≈0℃，工作效率高。

自動排空裝置分為兩種 :（低壓PN25以內）液囊熱敏元件組成和（過熱蒸汽系統）雙金屬片組成。

一、 Brief introduction of imported free floating ball steam trap

German "lock" imported free floating ball steam trap uses high-precision grinding stainless steel hollow ball to open or close the valve with the change of condensate level in the valve chamber. The structure of the trap is relatively simple, mainly composed of floating ball and automatic emptying device. Stainless steel hollow floating ball, the only action element in valve chamber, is manufactured by high-precision grinding process. The whole spherical surface can be used as sealing surface, without centralized wear during operation, with long service life; there is no vulnerable parts in the valve chamber, and the reliability is high. The floating ball can freely adjust the opening of valve hole according to the change of water level, and can discharge condensate continuously. The undercooling degree is about 0 ℃, and the working efficiency is high.

The automatic emptying device is divided into two types: (low pressure within PN25) liquid bag thermal element composition and (superheated steam system) bimetallic sheet composition.

三、進口自由浮球式蒸汽疏水閥工作原理：

進口自由浮球式蒸汽疏水閥的結構簡單，內部只有一個精細研磨的不銹鋼空心浮球，既是浮子又是啟閉件，無易損零件，使用壽命很長。裝置剛起動時，管道內出現空氣和低溫冷凝水，手動排空氣閥能迅速排除不凝結氣體，疏水閥開始進入工作狀態，低溫冷凝水流進疏水閥，凝結水的液位上升，浮球上升，開啟閥門。裝置很快提升溫度，管道內溫度上升到飽和溫度之前，自動排空氣閥已經關閉；裝置進入正常運行狀況，凝結水減少，液位下降，浮球隨液位升降調節閥孔流量；當凝結水停止進入時，浮球隨介質流向逼近閥座，關閉閥門。自由浮球式蒸汽疏水閥的閥座總處于液位以下，形成水封，無蒸汽泄漏。

The structure of the imported free floating ball steam trap is simple. There is only a fine ground stainless steel hollow floating ball inside, which is not only a float but also a opening and closing part. There is no vulnerable part and the service life is very long. When the device is just started, there is air and low-temperature condensate in the pipeline. The manual air exhaust valve can quickly remove the non condensable gas. The drain valve starts to enter the working state. The low-temperature condensate water flows into the drain valve, the liquid level of the condensate rises, the floating ball rises, and the valve is opened. The device quickly raises the temperature. Before the temperature in the pipeline rises to the saturation temperature, the automatic exhaust valve has been closed; when the device enters the normal operation condition, the condensate decreases, the liquid level drops, and the floating ball rises and falls with the liquid level to regulate the valve hole flow; when the condensate stops entering, the floating ball approaches the valve seat with the medium flow direction, and the valve is closed. The valve seat of the free float steam trap is always below the liquid level, forming a water seal without steam leakage.

四、進口自由浮球式蒸汽疏水閥選型條件：

1 、根據用汽設備最大耗汽量乘選用倍率（ 2 — 3 倍），為最大凝結水量來選疏水閥的排水量。

2 、疏水閥的最高工作壓差，（即閥前工作壓力減去閥后背壓）有背壓要注明。

3 、疏水閥的最高工作溫度。

4 、疏水閥使用工況。

5 、連接方式。

6 、閥體材料。

1. According to the maximum steam consumption of the steam equipment multiplied by the selected ratio (2-3 times), the drainage volume of the drain valve is selected as the maximum condensed water volume.

2. The maximum working pressure difference of the drain valve (i.e. the working pressure in front of the valve minus the back pressure behind the valve) shall be indicated if there is back pressure.

3. Maximum operating temperature of drain valve.

4. Operation condition of drain valve.

5. Connection mode.

6. Body material.

五、進口自由浮球式蒸汽疏水閥技術參數：

1、規格范圍：DN15-DN100

2、溫度范圍：-20℃≈450℃

3、壓力范圍：PN16-PN40

4、閥體材質：鑄鋼/不銹鋼/鉻鉬鋼

5、閥桿材質：不銹鋼

6、閥蓋材質：鑄鋼/不銹鋼/鉻鉬鋼

7、連接方式：法蘭，內螺紋連接

8、〖應用場合〗：水、水蒸汽。

1. Specification range: dn15-dn100

2. Temperature range: - 20 ℃ ~ 450 ℃

3. Pressure range: pn16-pn40

4. Valve body material: cast steel / stainless steel / chrome molybdenum steel

5. Stem material: stainless steel

6. Valve cover material: cast steel / stainless steel / chrome molybdenum steel

7. Connection mode: flange, internal thread connection

8. Application occasion: water and steam.